SERVICEThis radio is designed for easy servicing. Secondly, use your systems power supply (whichsupplies the voltage and current required for your system).Make sure sufficient air can flow around the radio and powersupply to allow adequate cooling. Which is as close as practical to the antenna cable entrypoint. Radio locationSelect a convenient location for your control station radio The antenna system selection dependson many factors and is beyond the scope of this manual.Your KENWOOD dealer can help you select an antenna sys-tem that will best serve your particular needs.Ĥ-2. INSTALLATION PLANNING CONTROL STATIONS4-1. If the cable must beextended, be sure the additional wire is sufficient for thecurrent to be carried and length of the added lead.Ĥ. The cable provided with the radio is sufficient to handlethe maximum radio current demand. Connect the ground lead directly to the battery negativeterminal.Ĥ. The vehicle ignition switch then controlsDC to the relay coil.ģ. Connecting the Positive lead toany other positive voltage source in the vehicle is not rec-ommended.ĬAUTIONIf DC power is to be controlled by the vehicle ignitionswitch, a switching relay should be used to switch the posi-tive power lead. Connect the positive power lead directly to the vehiclebattery positive terminal. Check the vehicle ground polarity before installa-tion to prevent wasted time and effort.Ģ. Reverse polarity will cause the cable fuseto blow.
![kct- 19 installation in kenwood tk 880 kct- 19 installation in kenwood tk 880](http://hubbrown.weebly.com/uploads/1/2/5/0/125076586/276262977.jpg)
This radio may be installed in negative ground electrical Position the radioclose enough to the vehicle operator to permit easy accessto the controls when driving.ģ-4. Allow sufficientspace around the radio for air cooling. Be sure the mounting surfaceis adequate to support the radios weight. RadioThe universal mount bracket allows the radio to be Thetrunk lid is preferred, bond the trunk lid and vehicle chassisusing ground straps to ensure the lid is at chassis ground.ģ-3. Large, flat conductive area, usually at the roof center. AntennaThe favored location for an antenna is in the center of a Plan cable runs for protection against pinching or crush-ing wiring, and radio installation to prevent overheating.ģ-2. Inspect the vehicle and determine how and where theradio antenna and accessories will be mounted. QT equipment operationshould be verified. Transmitter frequency, deviation, and power outputshould be checked, as should receiver sensitivity, squelchoperation, and audio output. TestingThe radio should be tested complete with all cabling andĪccessories as they will be connected in the final installa-tion. How-ever, it is recommended that receiver and transmitter op-eration be checked for proper operation before installation.Ģ-2.
![kct- 19 installation in kenwood tk 880 kct- 19 installation in kenwood tk 880](https://i.ebayimg.com/images/g/xEMAAOSwRUhY~AlE/s-l640.jpg)
IntroductionĮach radio is adjusted and tested before shipment. If any item is missing, please contactKENWOOD immediately.Ģ. Unpack the radio from its shipping container and checkfor accessory items. This equipment should be serviced by a qualified techni. All equipment should be properly grounded before SHUT OFF and DO NOT operate this equipment nearĮlectrical blasting caps or in an explosive atmosphere. DO NOT transmit until all RF connectors are verified se-Ĭure and any open connectors are properly terminated.
![kct- 19 installation in kenwood tk 880 kct- 19 installation in kenwood tk 880](http://www.repeater-builder.com/kenwood/pix/tk-860-programmer.jpg)
Nel safety : DO NOT transmit if someone is within two feet (0.6 PERSONNEL SAFETYThe following precautions are recommended for person.
![kct- 19 installation in kenwood tk 880 kct- 19 installation in kenwood tk 880](https://img.yumpu.com/23901784/1/500x640/kenwood-tk-8180-ko4bbs-home-page.jpg)
If thepart number is not known, include the chassis or kit numberof which it is a part, and a sufficient description of the re-quired component for proper identification.
Kct 19 installation in kenwood tk 880 full#
Tion, the full part identification number should be included.This applies to all parts : components, kits, or chassis. ORDERING REPLACEMENT PARTSWhen ordering replacement parts or equipment informa.
Kct 19 installation in kenwood tk 880 manual#
Changes which may occur after publication arecovered by either Service Bulletins or Manual Revisions.These are issued as required. It contains all required service in-formation for the equipment and is current as of the publica-tion data. This manual is intended for use by experienced techni-cians familiar with similar types of commercial grade com-munications equipment. B51-8524-10, in order to includenew variants with the following destination codes : E4. This Service Manual was revised based on the servicemanual as per parts No.